How To Clean Ls2 Rapid Helmet

Maintaining a clean LS2 Rapid helmet is an important part of motorcycle riding and can be a simple task if done correctly. A clean helmet is important for both safety and comfort, so it’s important to take the time to make sure your helmet is in top condition. This step-by-step guide will walk you through the process of cleaning your LS2 Rapid helmet, from removing the visor to cleaning and buffing the shell. With the right tools and a little bit of elbow grease, you can keep your helmet looking as good as new. So let’s get started!

Preparing your LS2 Rapid helmet

Before you start cleaning your helmet, you’ll want to make sure it’s ready for the job. There are a few things you should do to make sure your helmet is in great condition for cleaning: – First, make sure your helmet is clean. If your helmet has a build-up of dirt, sweat, or other grime, it can be more difficult to clean properly. Also, a dirty helmet may harbor bacteria, which can lead to skin irritation. Wipe the inside and outside of your helmet with a soft cloth to remove any loose dirt. We recommend using a non-ammonia cleaner so as not to damage the helmet’s material. – Check the fit of your helmet. If your helmet is too loose, the dirt will have a harder time staying out. Also, a helmet that is too loose might be uncomfortable for longer rides. If your helmet is too tight, it may be too painful to wear for any length of time. Make adjustments as necessary to make your helmet as comfortable as possible.

Removing the visor

First, you’ll want to remove the visor. By doing so, you will be able easily clean the inside of the helmet, including the padding and the chin strap. To remove the visor, gently pull up on the two side tabs of the visor and lift it out. Note that some visors may require you to remove screws before removing the visor. Once the visor is removed, you can clean the inside of the helmet. Be sure to use a clean towel to avoid damaging the inner padding of the helmet. You can also clean the chin strap by placing the strap between two fingers and sliding them along the length of the strap to remove dirt and grime. Next, use a soft, clean cloth to wipe down the outside of the helmet. Use a soft cloth to avoid scratching the helmet’s surface.

Cleaning the helmet’s shell

After the inside and outside of your helmet have been cleaned, it’s time to clean the helmet’s shell. First, you’ll want to remove the visor from the helmet to make cleaning easier. Start by removing the screws that hold the visor in place. Next, use a soft cloth to wipe down the outside of the helmet, followed by a clean, damp cloth to remove any dirt caked on the surface. Avoid using strong cleaners as they can damage the helmet’s surface. After cleaning the helmet’s outside, move on to the inside. Undo the velcro on the chin strap, unzip the lining of the helmet, and remove the padding. Next, use a soft brush and a mild soap to clean the inside. Be sure to use a gentle enough hand that you do not damage the helmet’s material.

Cleaning the helmet’s lining

The next step in cleaning your helmet is to clean the lining. Start by unzipping the lining and removing the padding. Next, use a mild soap to clean the lining of your helmet. Take care to use a soft enough hand to avoid damaging the helmet’s material. After the lining has been washed, you can let it air dry. Once the lining and padding have been cleaned, you can put the helmet back together.

Buffing the shell

The final step to cleaning your LS2 Rapid helmet is to buff the helmet’s shell to remove any scratches and give the helmet a polished look. Start by removing the gaskets from the helmet. These can be found on the inside of the helmet, and they will be the same colour as the helmet. Next, you’ll want to buff the helmet’s surface with a clean cloth. Use a mixture of water and mild soap to create a gentle buffing solution to remove scratches from the helmet’s surface. Be careful while buffing the helmet so you do not damage the helmet’s surface. Once the helmet has been cleaned and buffed, you can reattach the gaskets to the helmet.

Reattaching the visor

Once the helmet has been cleaned, it’s time to reattach the visor. First, take the time to clean the visor. You can do so by gently brushing the visor with a soft brush and wiping it down with a soft cloth. Once the visor has been cleaned, attach it to the helmet by sliding it into the slots on the helmet’s shell. Finally, you can put on your helmet and enjoy a freshly cleaned LS2 Rapid helmet!

Cleaning your LS2 Rapid helmet accessories

Your helmet may come with a variety of accessories, such as a face shield, chin strap, or visor clips. These items should be cleaned regularly to avoid damaging them and make them last longer. Start by removing the accessories from their respective places. Next, you can clean these items with a soft cloth. Be careful while cleaning the face shield to avoid scratching it. Once the accessories have been cleaned, you can put them back in their places and enjoy your freshly cleaned helmet!

Tips for keeping your helmet clean

There are a few ways to keep your helmet clean between cleanings. First, you can use a helmet cover so that the dirt does not get caught in the helmet’s material. These covers can be washed and reused between cleanings. You can also use a helmet liner, which you can wash regularly to remove dirt and sweat. You can also use a coat of helmet cleaner every once in a while to keep your helmet in tip-top shape. This will help remove grime that may get caught in the helmet’s crevices. Finally, make sure you are wearing the right helmet for your riding style and situation. If you ride on a daily basis, it’s important to wear a clean helmet each time. If you don’t have time to clean your helmet after every ride, make sure you are wearing the proper helmet for your riding situation.

Conclusion

After you have cleaned your helmet, you can use some sort of polish on the inside and outside of the helmet to gently buff away any scratches or scuffs. A quick buffing with a cloth will do the trick. If you’re particularly meticulous and want to take your helmet even further, you can use a light coat of clear sealer on the inside and outside of the helmet. Apply the sealer with a soft cloth and allow it to sit for a few minutes before buffing it with a soft cloth. This will help protect your helmet against bacteria and other germs that could be lurking inside your helmet. If you’re particularly concerned about the condition of your helmet, you can also invest in a helmet cover to protect your helmet’s finish against potential damage.

Leave a Reply

Your email address will not be published. Required fields are marked *