How To Replace Moen Faucet Cartridge 1224 B

Moen faucet cartridges are small, cylindrical devices that are installed inside faucets to control the flow of water. They’re often made of plastic and filled with rubber or silicone. Over time, these components may wear out or break, which will make it difficult to operate the faucet.

In this article, you will learn about how to replace a moen faucet cartridge 1224 B. It’s an easy job that can be done in under 30 minutes. The first step is to shut off the main water supply at the home’s water meter valve. You won’t be able to continue with this process if you don’t take this step! The next step is locating your old valve and replacing it with a new one of a different size.

What do you need?

You will need the following tools and materials for this job:

  • Wrench or socket wrench for shutting off the water supply
  • Screwdriver for removing the handle and cartridge
  • Plastic gloves to protect your hands from water and grime
  • Replacement cartridge for your model of faucet
  • Replacement washers for the faucet stem
  • Replacement gasket for the faucet body
  • Replacement screws for the handle
  • Replacement escutcheon plate
  • Replacement escutcheon screws
  • Replacement faucet handle.

How to change a moen faucet cartridge

The first step is to shut off the main water supply at the home’s water meter valve. You won’t be able to continue with this process if you don’t take this step! Next, you’ll need to remove the handle from the faucet. There are usually two small screws holding it in place. If you’re working with a single-handle faucet, they will be on the back side of the handle. If you’re working with a two-handle faucet, they will be on the front side of the handle. After removing the screws, lift the handle straight up and pull it off the faucet shaft. Next, you’ll need to unscrew the escutcheon plate on the faucet body. It’s the plate that covers the hole in the sink where the faucet is installed. If you’re working with a single-handle faucet, you’ll need to unscrew the plate on the top of the faucet body. If you’re working with a two-handle faucet, you’ll need to unscrew the plate on the bottom of the faucet body. After removing the escutcheon plate, you’ll be able to unscrew the old faucet cartridge. You can use a wrench, but you may find it easier to use a screwdriver. Be careful not to scratch the faucet body. After removing the old faucet cartridge, you’ll be able to inspect it and determine whether it can be repaired or if it needs to be replaced. If it can be repaired, you can use a utility knife to cut off the damaged section and replace it with a new piece of rubber. Now, you can install the new faucet cartridge. To do so, you’ll need to apply a thin layer of plumber’s tape to the threads of the faucet body. After that, you can screw in the new cartridge and tighten it using a wrench. Next, you can install the new escutcheon plate and tighten the screws. After that, you can install the new handle and tighten the screws holding it in place. Make sure that the handle is pointing in the correct direction before tightening it in place. After that, you can turn on the main water supply and test the faucet to make sure it works. If it doesn’t, you may need to repeat the process.

How to Install New Faucet Shaft and Handle Assembly

If you need to replace the faucet shaft, you’ll need to shut off the water supply at the water meter valve first. Next, you’ll need to unscrew the faucet from the sink and remove the old shaft and handle assembly. After that, you can screw the new shaft and handle assembly in place. You may need to apply a thin coat of plumber’s grease to the threads of the new shaft to prevent it from squeaking. After that, you can connect the faucet to the new shaft and turn on the water supply to test the new faucet. If it doesn’t work, you’ll need to repeat the process.

How to Install New Escalator Coiled Spring

If you need to replace the escalator coiled spring, you’ll need to shut off the water supply at the water meter valve first. Next, you’ll need to unscrew the faucet from the sink and remove the old spring. After that, you can screw the new spring in place. You may need to apply a thin coat of plumber’s grease to the threads of the new spring to prevent it from squeaking. After that, you can connect the faucet to the new spring and turn on the water supply to test the new faucet. If it doesn’t work, you’ll need to repeat the process.

Conclusion

A moen faucet cartridge is a small, cylindrical device that is installed inside faucets to control the flow of water. They’re often made of plastic and filled with rubber or silicone. Over time, these components may wear out or break, which will make it difficult to operate the faucet. In this article, you’ve learned how to replace a moen faucet cartridge. It’s an easy job that can be done in under 30 minutes.

Leave a Reply

Your email address will not be published. Required fields are marked *